Martha starts 090114

** Beam 6B dead; FAA radar is ON
** Short, gap filling run
 
** The drift is 49p2 +115524        
** This is a fall drift....
** The pos file name is therefore:    pos_090113p_+115524f.sav
**
-- Working in:  /export/coamo/a2010/09.01.13p
   cp /share/a2010-2/data/09.01.13p/*list* .
   gedit cal090113p.list
   gedit drift090113p.list
   >idl
   >@wasinit2
   >@alfinit


--  > callist='cal090113p.list'        
   > dir='/share/a2010-2/data/09.01.13p' 
   > calib1,callist,dcalON,dcalOFF,dir=dir
   > help,dcalon,/st
   > calib2,dcalON,dcalOFF,ncalib
   > Any bad boards in system?
   y
How many bad boards? [enter n]
: 2
Enter nbeam, npol of bad board
: 6,1
Enter nbeam, npol of bad board
: 7,1
   > help,ncalib,/st
   > save, ncalib,file='ncalib_090113p.sav'    
** There are 10 cal values for this run ***
** The calibration for this run looks fine. nfit=3

--  bpdgui
   Set the list of files (upper left; use "browse"): drift090113p.list.
   Enter the new calsession: calsession_090113p.sav
   Enter the new runpos: pos_090113p_+115524f.sav 
   set CRAT to "fit", not "median"
**The interp regions here are [3480 to 3520] **

-- restore,'pos_090113p_+115524f.sav'
   help,pos
** There are 10 drifts for this run **

-- restore,'pos_090113p_+115524f.sav'
-- restore,'d214400+294831.526180333.sav'
-- flagbb,dred,cont_pt,mask,pos,GAUSAV=11,HAN=3,AGC=1,n1=0,n2=6
   at end, save badboxes to file
   filename = bb
   then save pos file in case of crash
   save,pos,file='pos_090113p_+115524f.sav'
-------------------------------------------------------------------------------

  d013427+115525.901300175.sav  q1  1 AGC    strong FAA+mods  Beam 1.0 power beats; worse 1.1; drop it.

CGiovanardi & MGrossi start 090128

  d013427+115525.901300175.sav  q1  1 AGC    mild SW in 4.0,4.1;AGC 1139 in 0.0,0.1,2.1; pow_beats in 1,0(weight 3) & 1.1(weight 6)
  d014435+115525.901300177.sav  q1  1 AGC; 1 nonAGC in beams 0,3,5; mild SW in 3.0,3.1; beam 1 as before > same weights
  d015441+115525.901300179.sav  q1  1 AGC    mild SW in 3.0,3.2,5.0; pow_beat in 1.0(weight 3), 1.1(weight 7)
  d020448+115525.901300181.sav  q1           medium SW in 3.0,3.1; mild SW in 5.0,5.1; pow_beat in 1.0 (weight 3) & 1.1 (weight 7)
  d021454+115525.901300183.sav  q1  1 AGC    HVC; SW's as before; pow beat in 1.0 (weight 2) and 1.1 (weight 4)
  d022501+115525.901300185.sav  q1           HVC; SW's as before; pow beat in 1.0 (weight 2) and 1.1 (weight 5)
  d023507+115525.901300187.sav  q1           mild SW's in 3.0 3.1; pow beat in 1.0 (weight 2) & 1.1 (weight 5)
  d024514+115525.901300189.sav  q1           mild SW's in 3.0 3.1; pow beat in 1.0 (weight 3) & 1.1 (weight 6)
  d025520+115525.901300191.sav  q1  1/2 AGC  HVC?; mild SW in 3.0 3.1; pow beat in 1.0 (weight 3) & 1.1 (weight 6)
  d030528+115525.901300193.sav  q1  HVC?     mild SW in 3.0 3.1; pow beat in 1.0 (weight 2) & 1.1 (weight 4)

Revision after Martha's comments:
d013427+115525.901300175.sav revised march 11 2009
d014435+115525.901300177.sav revised march 11 2009
d015441+115525.901300179.sav revised march 13 2009
d020448+115525.901300181.sav revised march 13 2009
d021454+115525.901300183.sav revised march 13 2009
d022501+115525.901300185.sav revised march 13 2009
d023507+115525.901300187.sav revised march 13 2009
d024514+115525.901300189.sav revised march 13 2009
d025520+115525.901300191.sav revised march 13 2009
d030528+115525.901300193.sav revised march 13 2009




** Be sure to save your pos file regularly!
   save,pos,file='pos_090113p_+115524f.sav'
   
You can inspect the averaged, smoothed datasets for each beam using STRIP_PV and INSPECT
   strip_pv,dred,cont_pt,msmooth,n1=0,n2=6,showpol=3,gausav=11,han=5,rfimod=0,units=1
   inspect,msmooth,showpol=3,nstrip=4,agc=1

You can review your flagging using
   reviewbb,dred,cont_pt,mask,pos,GAUSAV=11,HAN=3,AGC=1,n1=0,n2=6

>   print,where(pos.badbox[0,0,0,2] eq 0)


This is a nice dataset with little RFI. FAA off!