Last update: 06Jul14 mph

Sarah Higdon & Josh Davidson starts 070114
FLAGGED RG/070305

**beam 1b bad, some lightning, some GPS @ 1381 MHZ around LST 12 28

 
** The drift is 18p2 +042253
** This is a spring drift....
** The pos file name is therefore:    pos_070113_+042253s.sav
**
-- Working in:  /share/a2010-2/work/gsu/07.01.13
   cp /share/a2010-2/data/07.01.13/*list* .
   gedit cal070113.list  
   gedit drift070113.list 

   >idl
   >@wasinit2
   >@alfinit

-- Perform the calibration, in 2 steps:
   > callist='cal070113.list'              
   > dir='/share/a2010-2/data/07.01.13'     
   > calib1,callist,dcalON,dcalOFF,dir=dir
   > help,dcalon,/st
   > calib2,dcalON,dcalOFF,ncalib

   > Any bad boards in system?
   Answer y,1,1

   The current mask will be displayed. Step though the beams. If ok,
   just hit return.

   The calratios (Cal/TPcalON-TPcalOFF) and Tsys will be displayed for
   the drift. Note the amplitude of the variation in calrat (~1 degree).
   If ok, hit "enter" and fit=1 (or 2 or 3... judge for yourself - think about
   the statistical significance of anything higher than 3 -- but sometimes
   curvature is needed and warranted!).
   Keep track of anything unusual (points deleted, high Tsys etc).

   Check that it created the file ok:
   > help,ncalib,/st


   > save, ncalib,file='ncalib_070113.sav'       

{Then comment on the calibration; was it "normal"? Did you have to delete points?}

** There are 18 cal values for this run ***
** The calibration for this run looks very nice. There is one CalRat for
   Beam 2, both pols, which is off; the Tsys is also high; probably a continuum
   source; point deleted. **

   If you want, you can plot some of the values:
   > restore,'ncalib_070113.sav'
   > plot,ncalib.rahr0,ncalib.decdeg0,psym=4

-- Set up and run the BPD gui.
   > bpdgui


   Enter the new calsession: calsession_070113.sav
   Enter the new runpos: pos_070113_+042253s.sav  
                                                     
   set CRAT to "fit"

**The interp regions here are [3476 to 3518] 

 run! 
AT THIS STEP SJUH

When that is done, check that the pos file has been correctly written.

-- restore,'pos_070113_+042253s.sav'
   help,pos
   This should tell you that "pos" is array with dimension equal to the
   number of drifts that were processed.

** There are 33 drifts for this run **

RESTARTED BY RG/070305 

d072501+042248.701301397.sav	q1 1 agc
d073508+042248.701302002.sav	q1
d074514+042248.701302607.sav	q1
d075521+042248.701303212.sav	q1.5 bm 4/0 ratty
d080528+042248.701303817.sav	q1.5
d081534+042248.701304422.sav	q1.5
d082541+042248.701305027.sav	q1.5
d083548+042248.701305632.sav	q1.5
d084554+042248.701306237.sav	q3	v loud GPS rec 180-280
d085601+042249.701306842.sav	q1.5
d090608+042248.701307447.sav	q1.5	ragged, unstable power levels
d091614+042248.701308052.sav	q1.5
d092621+042248.701308657.sav	q3	GPS 0-110, 570-599
d093628+042248.701309262.sav	q3 	GPS 0-200
d094635+042248.701309867.sav	q1.5 several
d095641+042248.701310472.sav	q1.5
d100648+042248.701311077.sav	q1.5
d101655+042248.701311682.sav	q1.5 3agc
d102701+042248.701312287.sav	q1.5 >4
d103708+042248.701312892.sav	q1.5
d104715+042248.701313497.sav	q1.5
d105722+042248.701314102.sav	q2
d110728+042248.701314707.sav	q2 several
d111735+042248.701315312.sav	q1.5 few
d112742+042248.701315917.sav	q1.5
d113749+042248.701316522.sav	q2.5 GPS 175-230
d114755+042248.701317127.sav	q1.5	ragged, unstable power levels esp bms 0, 3-5
d115802+042248.701317732.sav	q1.5
d120809+042248.701318337.sav	q1.5
d121816+042248.701318942.sav	q1.5
d122822+042248.701319547.sav	q2.5 GPS 355-415 several
d123829+042248.701320152.sav	q1.5 several
d124836+042248.701320757.sav	q2 several, power jumps